Doors Advice 02 - How to Fix a Draughty Front Door: A Step-by-Step Guide
A draughty front door can make your home less energy-efficient and uncomfortable, especially during the colder months. Fixing draughts around your front door is a simple yet effective way to keep your home warm, reduce heating bills, and increase comfort. In this guide, we’ll explain how to identify and fix draughts around your front door.

Common Causes of Draughts
Before you start fixing the draughts, it’s important to identify where they’re coming from. Common sources of draughts around a front door include:
- Gaps between the door and frame: These gaps can develop over time due to wear and tear or poor fitting.
- Worn or missing weatherstripping: Weatherstripping, which seals the gaps around the door, can degrade over time, allowing cold air to enter.
- Letterbox flap: A poorly fitted or damaged letterbox can be a significant source of draughts.
- Keyhole or locks: Gaps around the keyhole or door locks may allow cold air in.
- Door threshold: If the threshold (the bottom edge of the door) is not sealed properly, it can allow draughts.
Tools and Materials You’ll Need:
- Weatherstripping tape (foam or rubber)
- Draught excluder (for the bottom of the door)
- Brush seal for the letterbox
- Keyhole cover
- Sealant or caulk
- Caulking gun
- Screwdriver set
- Utility knife or scissors
- Measuring tape
- Door sweep (optional)
- Expanding foam (optional, for larger gaps)
Step 1: Identify the Draughts
The first step in fixing a draughty door is identifying where the cold air is entering. To do this:
- Visual inspection: Check for obvious gaps or damage around the door frame, letterbox, and keyhole.
- The candle test: Light a candle or hold a piece of tissue paper near the edges of the door. If the flame flickers or the paper moves, it indicates a draughty spot.
- Check at night: If light from the outside is visible around the edges of the door, there are likely gaps that need sealing.
Step 2: Replace or Add Weatherstripping
Weatherstripping is an essential material for sealing the gaps between the door and its frame. Over time, it can wear out and lose its effectiveness, leading to draughts.
- Remove old weatherstripping: If the weatherstripping is old or damaged, peel it away from the door. Use a utility knife to remove any adhesive residue.
- Measure the door frame: Measure the height and width of your door frame to ensure you cut the new weatherstripping to the correct size.
- Apply new weatherstripping: Choose either self-adhesive foam or rubber weatherstripping. Cut the strips to size with scissors or a utility knife and press them firmly into place along the edges of the door frame. Ensure that the strips create a snug seal when the door is closed.
- Check the seal: Close the door and check whether the new weatherstripping forms a tight seal. Adjust if necessary to ensure no gaps remain.
Step 3: Install a Draught Excluder
Draughts often come from the gap at the bottom of the door. A draught excluder is an easy and affordable solution to block cold air.
- Choose your draught excluder: You can either buy a fabric draught excluder (sometimes called a ‘door snake’) or install a permanent door sweep. A door sweep has a brush or rubber strip that seals the bottom edge of the door.
- Install the draught excluder: For a door sweep, measure the width of your door and cut the sweep to fit. Most door sweeps are screwed into place at the bottom of the door. Use a screwdriver to fix it securely, ensuring the sweep lightly touches the floor but doesn’t hinder the door’s movement.
Step 4: Fix Draughts Around the Letterbox
The letterbox can be a major source of draughts. Fitting a brush seal or insulated letterbox cover can help.
- Remove the old letterbox flap (if necessary): If your existing letterbox flap is damaged, remove it using a screwdriver.
- Install a new brush seal or flap: Choose a letterbox with an integrated brush seal, or install a separate brush strip inside the letterbox. This will block cold air while still allowing post to come through.
- Fit an exterior letterbox cover: For added protection, fit a letterbox cover on the inside of your door. These covers usually come with self-adhesive backing or screws for easy installation.
Step 5: Seal the Keyhole
The keyhole may allow draughts to enter, particularly if you have a large or traditional keyhole.
- Install a keyhole cover: Purchase a keyhole cover (also called an escutcheon), which will fit around the keyhole and prevent draughts when the key isn’t in use. These are usually installed with screws or adhesive.
- Check the seal: Make sure the keyhole cover fits snugly over the hole and isn’t too loose.
Step 6: Seal Gaps Around the Door Frame
If there are gaps between the door frame and the wall, these can be sealed with caulk or expanding foam.
- Apply caulk: Use a caulking gun to apply a bead of exterior caulk around the outside edges of the door frame. This will block draughts and moisture.
- Use expanding foam for larger gaps: If there are significant gaps around the frame, apply expanding foam to fill the voids. Be careful not to use too much foam, as it can expand excessively and damage the frame.
Step 7: Check and Adjust the Door Alignment
If your door is misaligned, it may not close properly, leaving gaps where draughts can enter.
- Tighten the hinges: Use a screwdriver to tighten the door’s hinges. Over time, loose hinges can cause the door to sag, leaving gaps at the top or bottom.
- Adjust the door threshold: If the threshold (the part of the frame the door closes against) is adjustable, raise or lower it to ensure the door fits tightly against it when closed.
Step 8: Insulate the Glazing (If Applicable)
If your front door has glass panels, they may also be a source of draughts. Consider upgrading to double-glazed units or applying window film for additional insulation.
Final Checks and Maintenance
Once you've completed all the steps, test the door again for draughts. Use the candle or tissue test to check for any remaining gaps. Regularly check and replace weatherstripping and draught excluders as part of your home maintenance to ensure they continue to provide an effective seal.
Additional Tips:
- Regularly check seals: Over time, weatherstripping and draught excluders can wear out, so it’s a good idea to inspect them annually.
- Invest in energy-efficient doors: If your front door is particularly old or poorly insulated, consider upgrading to a modern, energy-efficient door. Many uPVC or composite doors come with built-in insulation and weatherproofing.
- Professional help: If you're unsure or uncomfortable with DIY work, you may want to hire a professional to help with more complex tasks such as adjusting the door alignment or installing new seals.
By following these steps, you’ll be able to significantly reduce draughts around your front door, keeping your home warmer and more energy-efficient throughout the year.
Disclaimer: Sunlight holds no responsibility for any work that you or anyone else carries out based upon the information contained within these help pages (i.e. prices and information contained may change at any time) - we are simply offering various suggestions to help ease your pain and lower your stress levels. For peace of mind, we always recommend using insured and trained personnel to carry out any work, to obtain an up-to-date quotation from at least three suppliers and to get as much information as possible from the company whom you choose to conduct business with.
Call in the Professionals!
01565 650 195
Why attempt to take on complicated work yourself? It could end up costing you more. Instead, make contact with our pro-maintenance team for a consultation to discuss your needs today. Understandably, for the work to be cost-effective, you must live within a 20 mile radius of Knutsford.
Visit our showroom:
Sunlight Windows & Conservatories
Fryers Garden Centre
Manchester Road
Knutsford
Cheshire
WA16 0SX

Leave a reply